Plasmon V15 Uživatelský manuál stáhnout pdf (Strana 98)

Plasmon

15 AIT Tape Library User Manual

Page 96

Removing the Tape Drive

1. Disconnect the SCSI cables from the back of the tape drive. The SCSI connectors for the

tape drive are accessible from the back panel.

Figure 30. SCSI Connectors

2. From the back panel, use a #2 Phillips cross recess screwdriver to release the captive screw

that secures the tape drive carrier to the library, as shown in the following figure.

Figure 31. Removing the Tape Drive Carrier

Tape drive

SCSI connectors

Captive screws

Handle

1 2 ... 93 94 95 96 97 98 99 100 101 102 103 ... 137 138

Copyright 3
Disclaimer 3
Trademark Notices 3
Revision History 3
Safety Agency Standards 4
FCC Notice 4
Laser Safety Notice 4
European Notice 5
Australia/New Zealand 5
Product Warranty Caution 6
First Time Installation 7
Operation 7
Troubleshooting and Service 7
Table of Contents 9
Page 10 12
List of Figures 13
Page 12 14
List of Tables 15
Page 14 16
Product Overview 17
Library Features 18
Library Components 19
Back Panel Components 20
Internal Components 21
Page 20 22
NSTALLATION 23
Unpacking the Library 24
Selecting Cartridges 25
Selecting Cleaning Cartridges 26
Preparing Cartridges 27
Page 26 28
Hardware Installation 29
Page 28 30
Page 30 32
Connecting the Power Cord 33
Powering on the Library 34
Using the Operator Panel 36
Configuration 37
Configuring the Library 39
Description 40
Setting the SCSI IDs 41
Setting the Emulation Mode 42
Setting the Autoclean Option 44
Page 44 46
Page 46 48
Checking the Setup 50
Beginning Library Operations 50
Setting Ethernet Addresses 52
Ethernet 53
Page 52 54
Monitoring the Ethernet LEDs 56
PERATION 57
Opening the Front Door 58
Replacing the Magazine 59
Storing Cartridges 60
Sequential options 62
Setting Sequential Options 63
Avoiding Interruptions 64
Cartridge 67
Inventory 67
Resetting the Library 68
Performing Hardware Exercises 68
Using the Demo Menu 69
Using the Command Menu 70
Viewing Statistics 72
Viewing System Sensors 74
System Sensor Description 75
Page 74 76
Monitoring Tape Drive Status 78
Page 78 80
Cleaning the Tape Drive 83
Page 82 84
Ejecting a Cartridge Manually 85
Resetting a Tape Drive 86
IAGNOSTICS 87
Connecting the Serial Cable 88
Page 88 90
Diagnostics and Firmware 91
Page 90 92
Connecting to an FTP Utility 93
Upgrading Firmware via FTP 93
Page 92 94
AINTENANCE 95
Cleaning the Library 96
Replacing the Tape Drive 96
Preparing for Replacement 97
Tape drive 98
SCSI connectors 98
Installing the Tape Drive 99
Plasmon 100
Page 98 100
Maintenance and Service 101
Blank panel 102
Page 101 103
Packing the Library 104
Page 103 105
Page 104 106
ROUBLESHOOTING 107
Page 106 108
Troubleshooting 109
Page 107 109
Page 108 110
PECIFICATIONS 111
Power Cord Requirements 112
Ethernet Cable Requirements 113
Pin number Function 114
ONFIGURATION 115
SCSI Bus Termination 116
PECIFICATION 117
Encodation 118
Quiet Zone 118
Optical Specification 119
Label Dimensions 120
Specification Dimension 121
Volume Identifier Formats 122
Appendix C 123
Page 121 123
Description Corrective Action 125
Page 130 132
Page 131 133
Page 132 134
Page 133 135
Page 134 136
Contacting Plasmon 137

Komentáře k této Příručce

Žádné komentáře

Plasmon V15 Uživatelský manuál Strana 98

Komentáře k této Příručce

Související produkty a manuály pro Hardware Plasmon V15